Your Message

With the exploration and innovation of Bebon people, DEN gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel, and established our own Machining processing center in order to meet customer's diverse requirements.




Ympress® S355MC Strong, consistent and highly formable

Ympress® S355MC Strong, consistent and highly formable Ympress® S355MC is a hot rolled, high strength low alloy steel. It combines high strength with outstanding formability and consistent quality. It replaces conventional construction steel for applications where high strength is paramount. It is ideal for load bearing and

Reply
Material Properties of S355 Steel An Overview

Aug 23, 2015 · S355 is named based on it's minimum yield strength of 355 Mpa (N/mm2), However the yield strength reduces when you go up in thickness above 16 mm for flat products & hollow sections. Here is the table showing reduction in yield strength based on thickness. Up to 16 mm 355 Mpa.

Reply
High Strength Low EN 10149 2 S355MC Steel Plate Supplier

Our firm has attained a wide acknowledgment in providing S355MC High Tensile EN 10149 2 Plates to the customers. Supported by a rich manufacturing practice, we are involved in providing a praiseworthy range of S355MC High Tensile EN 10149 2 Coils.

Reply
Structural SteelS235, S275, S355 (3) Yield Strength

Yield Strength. The yield strength of structural steel measures the minimum force required to create a permanent deformation in the steel. The naming convention used in European Standard EN10025 refers to the Minimum Yield strength of the steel grade tested at 16mm thick.

Reply
S355MC BEBON steel

S355MC steel plate is mainly used as high yield strength steels for cold forming steels. The EN10149 S355MC steel is equivalent to SEW092 QStE380TM and NFA E355D steel grades. The EN10149 S355MC steel is equivalent to SEW092 QStE380TM and NFA E355D steel grades.

Reply
Table of material properties for structural steel S235

Nominal values of structural steel yield strength and ultimate strength For structural design according to Eurocode 3 (EN1993 1 1), the nominal values of the yield strength f y and the ultimate strength f u for structural steel are obtained as a simplification from EN1993 1 1

Reply
DATASHEET11 02 03 GB8413 DOMEX Domex 355 MC

Yield strength Tensile strength Elongation on failure R eH N/mm 2 min R m N/mm min max < 3 mm A 80 % min > 3 mm A 5 % min 355 430 550 19 23 BENDABILITY Nominal sheet thickness, t <3 mm 3 mm <t 6 mm >6 mm Min. recommended bending radius (<90 º) 0,2 xt 0,3 xt 0,5 xt DATASHEET11 02 03 GB8413 DOMEX Domex 355 MC Hot rolled, high strength, cold forming steel Page 1/2

Reply
Brief portrait Technical features Chemical composition

Coil inner diameterstandard 508 mm / optional 610 mm Coil outer diametermax. 1,890 mm Coil weightmax. 20.5 kg/mm strip width Strip widthmax. 720 mm Strip thickness1.5 – 16 mm. thyssenkrupp Steel Precision Steel S355MC / HSM 355 Version 1/18 2. thyssenkrupp Hohenlimburg GmbH, Oeger Str.

Reply
S355 European Standard Steel joostdevree.nl

S355 structural steel plate is a high strength low alloy European standard structural steel covering four of the six "Parts" within the EN 10025 – 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry and physical properties similar to ASTM A572 / 709. Careful attention should always be placed on the specific

Reply
S420MC / 1.0980 SteelNumber Chemical composition

Chemical composition of steel S420MC (1.0980), Standards of steel S420MC (1.0980) Mechanical Properties of steel S420MC (1.0980) Equivalent grades of steel S420MC (1.0980) steel S420MC (1.0980) Tensile Strength, Elongation, Proof strength , Hardness

Reply
Strenx® High performance structural steel SSAB

Strenx® is a high strength, high performance structural steel that helps make products stronger, The steel’s properties — yield and tensile strength, bending performance, impact toughness — are carefully tested to ensure reliability and consistency in every delivery. Performance portfolio.

Reply
SSAB Domex 355MC

Yield strength R eH (min MPa) Tensile strength R m (MPa) Elongation A 80 1) (min %) Elongation A 5 2) (min %) Min ner bending radius for a 90° bend 1.80 3 355 430 550 19 23 0.2 xt 3.01 6 355 430 550 23 0.3 xt 6.01 16 355 430 550 23 0.5 xt The mechanical properties are valid in

Reply
EN 10149 2 Grade S355MC thermomechanically rolled

The thermomechanical rolled steel S355MC, mat. no. 1.0976, is used for cold formed components like vehicle frames, axles and special sections. Tempering > 580 deg. leads to an decrease of the strength of the thermomechanical treated material. The lowest application temperature amounts to 20 deg.

Reply
What is the difference between S355JR and S355J2 steel

What is the difference between S355JR and S355J2 steel steel plate. Leave a Message Get a price EX Stock Promotion Center. S355JR and S355J2 steel are widely used structure steel under standard EN10025 2. The two steel grades have much in common, as they have same Min. yield strength 355Mpa.

Reply
EN 10149 2 Grade S420MC thermomechanically rolled

The thermomechanical rolled steel S420MC, mat. no. 1.0980, is used for cold formed components like vehicle frames, axles and special sections. Tempering > 580 deg. leads to an decrease of the strength of the thermomechanical treated material. The lowest application temperature amounts to 20 deg.

Reply
EN 10025 2 S355J2G3 high strength structural steel plate

S355J2G3 is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel. With its low carbon equivalent, it possesses good cold forming properties. The plate is produced by fully killed steel process and supplied in normalized or controlled rolling condition.

Reply
bebonchina Steel Plate,Steel Plate Sheet,Profiled

WORLD CLASS SUPPLIER OF STEEL MATERIAL. During the past 18 years since 2000, BBN not only shared 2000000 tons steel with customers from more than 70 countries, but also devoted to be the most professional steel supplier and biggest stockist in China and recognized by global customers with full range products, best price, strict quality control,advanced service concept and the fastest delivery

Reply
productinformation precidur S355JR thyssenkrupp

Tensile strength R m [MPa] Elongation A 5 [%] A 80 [%] Rolled condition* min. 355 470 – 630 min. 22 min. 18 * The mechanical characteristics shown match the “JR” variant (EN10025 2) in thicknesses ≥ 3.0 mm. Restricted mechanical property ranges can be agreed on request.

Reply

Your Message