Your Message

With the exploration and innovation of Bebon people, DEN gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel, and established our own Machining processing center in order to meet customer's diverse requirements.




ASTM A53 Grade A & B Steel Pipe Chemical Composition

Strength Grade A Grade B Tensile strength, min, psi [MPa] 48 000 60 000 Yield strength, min, psi [MPa] 30 000 35 000 Elongation in 2 in. or 50 mm e = 625 000 A 0.2 /U 0.9 or Table X4.2 and X4.2

Reply
ASTM A53 Pipe Specifications American Piping Products

American Piping Products stocks a full range of A53 pipe (SA53 Pipe) inGrade B; NPS 1/8” to 26” diameter; Schedules 10 through 160, STD, XH and XXH

Reply
API 5L Line Pipe Physical Properties, Yield Strength

Line pipe grade designations come from API Spec 5L Specification for Line Pipe. Standard Line Pipe has grade designation A and B. Stronger grades have the designation X followed by the specified minimum yield strength of the pipe steel, measured in kilopounds per square inch (abbreviated ksi), e.g. X60 for pipe having a minimum yield strength

Reply
ASTM A106 Pipe Specifications American Piping Products

Inspection test pressures produce a stress in the pipe wall equal to 60% of specified minimum yield strength (SMYS) at room temperature. Maximum Pressures are not to exceed 2500 psi for NPS3 and must stay under 2800 psi for the larger sizes. Pressure is maintained for not less than 5 seconds.

Reply
Different ERW Standard and Line Pipe Grades HYSP Steel

HYSP Steel Pipe supply you ERW Steel Tubing 12inch ASTM A53 B SCH40 or API 5L ERW steel pipes for your gas and oil line pipe or water pipes application.

Reply
Differences between ASTM A53 B and ASTM A106 B Steel Pipe

ASTM A53 B mechanical strength is the same with ASTM A106 B steel pipe, Tensile strength maximum 415 Mpa, Yield strength maximum 240 Mpa. ElongationFor A53 pipe there are 2 methods to calculate elongation. BSee ASTM A53 elongation value table X4.1 or table X4.2 for different specimen area.

Reply
TOTAL CAPABILITIES IN THE PIPELINE INDUSTRY

Dec 03, 2012 · pipe 0.28% for grades >= B 0.24% Chemistrymax C for welded pipe 0.26% for grades >= B 0.22% Chemistrymax P 0.030% for grades >= A 0.025% Chemistrymax S 0.030% 0.015% Carbon equivalent Only when purchaser specifies SR18 Maximum required for each grade Yield Strength, maximum None Maximum required for each grade

Reply
Learn about ASTM A53 Grade A & Garde B Pipe Types and

ASTM A53 is one of the widely used standard specification for Steel Pipe that used in the Oil and Gas as well as other process industries also. ASTM A 53 Grade B is more popular than other grades. These pipes can be bare pipes without any coating, or it may be Hot Dipped or Zinc Coated and manufactured by Welding or by a Seamless manufacturing process. In Oil and Gas ASTM A53 pipes are used in

Reply
X80 Steel

X80is the number in the American Petroleum Institute's API Spec 5L Pipeline Specification. X represents the pipeline steel in the API Spec 5L standard, 80 is the strength grade, the unit is kpsi, and X80 is the pipeline steel with a minimum yield strength of 80 kpsi, which is converted to a metric unit of approximately 555 MPa.

Reply
49 CFR § 192.107 Yield strength (S) for steel pipe

§ 192.107 Yield strength (S) for steel pipe. (a) For pipe that is manufactured in accordance with a specification listed in section I of appendix B of this part, the yield strength to be used in the design formula in § 192.105 is the SMYS stated in the listed specification , if that value is known.

Reply
A500 Spec Sheet American Piping Products

A For each reduction of 0.01 percentage point below the specified maximum for carbon, an increase of 0.06 percentage point above the specified maximum for manganese is permitted, up to a maximum of 1.50% by heat analysis and 1.60% by product analysis. B If

Reply
Carbon Steel Pipe an overview ScienceDirect Topics

For years, most pipes were made from Grade B steel, which has a minimum yield strength of 35,000 psi. Construction of high pressure, large diameter, cross country transmission lines created a need for high strength field weldable steel that would allow a substantial savings in steel tonnage.

Reply
API 5L Pipe Specifications (Seamless and Welded ) Enpro Pipe

Material in Carbon Steel and covers Grade B, X42, X46, X52, X56, X60, X65, X70, PSL1 and PSL2. Suffix letter for API 5L Pipe means the delivery condition which these for PSL2 pipe and belong to the steel grade, normally we see the pipe description with API 5L X60QS, or API 5L X42N, X52Q, these letters means Yield Strength and Tensile

Reply
What Is the Yield Strength of a Schedule 80 Galvanized

Rocky Mountain Steel Peering, meanwhile, produces schedule 80 piping with a minimum yield strength range of 35 KSI to 42 KSI, or 35,000 to 42,000 PSI. According to ASTM A653 standards, mild hot dip galvanized steel must have a minimum yield strength of 36,300 PSI.

Reply
ASTM A500 Steel Structure Tube

A500 Grade Tensile Strength Yield Strength; Grade B (Round) 58,000 (400) 42,000 (290) Grade C (Round) 62,000 (425) 46,000 (315)

Reply
Material Grade Comparison Chart Pipes

Material Grade Comparison Chart Pipes * The above chart is for comparison reference purposes only. User to use at own discretion. Category based on Yield Strength and Tensile Strength CVN Temp ASTM API 5L API 2W / 2H EN 10225 Seamless Hollow Sections EN 10025 2 EN 10025 3 (Normalized) EN 10025 4 (TMCP) ABS / BV / LR DNV GL

Reply

Your Message